EXTENDERS

DVI Fiber extender - SET

1920x1200 @ 60P FULL-HD / WUXGA

Extend your DVI signal from 75 meters up to 400 meters with the Axept EXDO in combination with Neutrik OpticalCON fiber cables.
Strong case for rental use, easy to transport, no loose small cables, one solution.

Neutrik DANTE Input/Output Interface

Chassis connector with black chromium plating, 4 solder contacts, 1 LC-Duplex feedthrough socket and 1 shell ground contact (for SMPTE cable shield), waterproof acc. to IP 65, front panel mount The chassis connector acts as a "feed-through" allowing simplified installations by connecting a conventional LC-Duplex on the rear. It is built in the standard D size shell and features an automatic sealing cover for maximum dust and dirt protection and a Push-Pull locking mechanism for safe connection. Colored sealings are included to identify the fiber mode. Not compatible to SMPTE 344M standard. Suitable for indoor (studio) camera links considering specific conditions acc. to IEC 60664-1 like pollution degree 1, overvoltage category 1 and rated voltage. Features & Benefits •Suggested OEM equipment connector due to LC front compatibility •Designed as feedthrough with automatic sealing shutter •Shutter with silicone gasket protects optical connection from dust and dirt •Suitable for indoor (studio) camera links considering specific conditions acc. to IEC 60664-1 like pollution degree 1, overvoltage category 1 and rated voltage •Accommodates standard LC connectors on the rear for simple installation •Connection on the front side either by rugged opticalCON or standard LC connector •The low cost of the chassis connector makes it a viable alternative to traditional connectors in fixed installations •Water resistant according to IP65 ingress protection in mated condition •In case of limited space the chassis can be mounted without rubber gasket. IP rating for this is IP52. •Color coded rubber sealing to identify fiber mode: Multimode - black Single mode PC - blue Single mode APC - green

Neutrik Adapter bracket for DANTE Interface

Chassis connector with black chromium plating, 4 solder contacts, 1 LC-Duplex feedthrough socket and 1 shell ground contact (for SMPTE cable shield), waterproof acc. to IP 65, front panel mount The chassis connector acts as a "feed-through" allowing simplified installations by connecting a conventional LC-Duplex on the rear. It is built in the standard D size shell and features an automatic sealing cover for maximum dust and dirt protection and a Push-Pull locking mechanism for safe connection. Colored sealings are included to identify the fiber mode. Not compatible to SMPTE 344M standard. Suitable for indoor (studio) camera links considering specific conditions acc. to IEC 60664-1 like pollution degree 1, overvoltage category 1 and rated voltage. Features & Benefits •Suggested OEM equipment connector due to LC front compatibility •Designed as feedthrough with automatic sealing shutter •Shutter with silicone gasket protects optical connection from dust and dirt •Suitable for indoor (studio) camera links considering specific conditions acc. to IEC 60664-1 like pollution degree 1, overvoltage category 1 and rated voltage •Accommodates standard LC connectors on the rear for simple installation •Connection on the front side either by rugged opticalCON or standard LC connector •The low cost of the chassis connector makes it a viable alternative to traditional connectors in fixed installations •Water resistant according to IP65 ingress protection in mated condition •In case of limited space the chassis can be mounted without rubber gasket. IP rating for this is IP52. •Color coded rubber sealing to identify fiber mode: Multimode - black Single mode PC - blue Single mode APC - green

Neutrik truss yoke kit for DANTE devices

Chassis connector with black chromium plating, 4 solder contacts, 1 LC-Duplex feedthrough socket and 1 shell ground contact (for SMPTE cable shield), waterproof acc. to IP 65, front panel mount The chassis connector acts as a "feed-through" allowing simplified installations by connecting a conventional LC-Duplex on the rear. It is built in the standard D size shell and features an automatic sealing cover for maximum dust and dirt protection and a Push-Pull locking mechanism for safe connection. Colored sealings are included to identify the fiber mode. Not compatible to SMPTE 344M standard. Suitable for indoor (studio) camera links considering specific conditions acc. to IEC 60664-1 like pollution degree 1, overvoltage category 1 and rated voltage. Features & Benefits •Suggested OEM equipment connector due to LC front compatibility •Designed as feedthrough with automatic sealing shutter •Shutter with silicone gasket protects optical connection from dust and dirt •Suitable for indoor (studio) camera links considering specific conditions acc. to IEC 60664-1 like pollution degree 1, overvoltage category 1 and rated voltage •Accommodates standard LC connectors on the rear for simple installation •Connection on the front side either by rugged opticalCON or standard LC connector •The low cost of the chassis connector makes it a viable alternative to traditional connectors in fixed installations •Water resistant according to IP65 ingress protection in mated condition •In case of limited space the chassis can be mounted without rubber gasket. IP rating for this is IP52. •Color coded rubber sealing to identify fiber mode: Multimode - black Single mode PC - blue Single mode APC - green

AXE-EXDO + PER-HC430S + Custom foam + 2x First power + 2x DVI to HDMI cable